1
Introduction
1.1 The gyro-compass should determine the direction of the head of
the high-speed craft (HSC) in relation to geographic (true) north.
1.2 In addition to the general requirements contained in resolution
A.694(17), the gyro-compass equipment installed in craft operating under the following
conditions:
-
.1 speed exceeding 30 knots and up to 70 knots;
-
.2 maximum rate of turn 20°/s; and
-
.3 normal range of operation between 70°N and 70°S should, as
required by chapter 13 of the HSC Code, comply with the minimum performance
requirements specified in these standards.
1.3 The gyro-compass, within a speed range of up to 30 knots, should
comply with the requirements of resolution A.424(XI), and within a speed range of 30
knots to 70 knots should comply with the requirements of this resolution.
1.4 A qualitative description of the effects of gyro-compass errors
due to high speed, accelerations, course changes, sea state, etc., and a qualitative
description of corresponding errors in other navigational aids, should be provided to
the user.
2
Definitions
For the purpose of these performance standards, the following definitions apply:
2.1
Gyro-compass means both the gyro-compass as heading sensor and the associated
heading transmission system.
2.2
True heading means the horizontal angle between the vertical plane passing
through the true meridian and the vertical plane passing through the craft’s fore and
aft datum line. It is measured from true north (000°) clockwise through 360°.
2.3 The compass is said to be settled if any three readings
taken at intervals of 30 min, when the compass is on a level and stationary base, are
within a band of 0.7°.
2.4 Settle point heading means the mean value of 10 readings taken at
20-minute intervals after the gyrocompass has settled as defined in 2.3.
2.5
Settle point error means the difference between settle point heading and true
heading.
2.6 Other errors to which the gyro-compass is subject are defined as the
difference between the observed value and the settle point heading.
3
Method of Presentation
Gyro-compass equipment should include the provision of a compass card or analogue
repeater for steering purposes and equipment for the purpose of taking visual bearing.
It should be graduated at equal intervals of one degree or a decimal fraction thereof. A
numerical indication should be provided at every 10° starting from 000° clockwise
through 360°. Additionally, a digital display may be provided. When a digital display is
provided, the course should be displayed as three digits plus, optionally, a fourth
digit indicating tenths of a degree. When a gyro-compass with digital display is used it
should incorporate a turning indicator.
4
Accuracy
4.1 Performance under static conditions (Settling of equipment)
4.1.1 When run-up in accordance with the manufacturer’s instructions, the
gyro-compass should settle within 6 h in latitudes of up to 70°.
4.1.2 The settle point error as defined in 2.5 at any heading and at any latitude
up to 70° should not exceed ±0.75° ✕ secant latitude where heading indications of the
gyro-compass should be taken as the mean of 10 readings at 20 min intervals, and the
root mean square value of the differences between individual heading indications and the
mean should be less than ±0.25° ✕ secant latitude.
4.1.3 The repeatability of settle point error from one run-up to another should
be within 0.25 ✕ secant latitude.
4.2 Performance under operational (dynamic) conditions
4.2.1 When run-up in accordance with the manufacturer’s
instructions, the gyro-compass should settle within 6 h in latitudes of up to 70° when
rolling and pitching with simple harmonic motion of any period between 6 s and 15 s, a
maximum angle of 5°, and a maximum horizontal acceleration of 0.22 m/s2.
4.2.2 The repeatability of the settle point error of the master gyro-compass
should be within ±1° ✕ secant latitude, including variations in magnetic fields and
changes in temperature as required by resolution A.694(17), etc., likely to be
experienced in the craft in which it is installed.
4.2.3 In latitudes of up to 70° N or S in craft operating within a latitude band
of 10°:
-
.1 the residual steady state error, after correction for speed
and course influences at a speed of 70 knots, should not exceed ±0.25° ✕ secant
latitude;
-
.2 the maximum error due to a rapid alteration of speed of 70°
knots should be kept to a minimum, and should not exceed ±2°;
-
.3 the error due to a rapid alteration of course of 180° at a maximum rate
of turn of 20°/s in any azimuth direction at a speed of 70 knots should not exceed
±3°; and
-
.4 the transient and steady state errors due to the craft rolling, pitching
and yawing, with simple harmonic motion of any period between 6 s and 15 s,
maximum angle of 20°, 10° and 5° respectively, and maximum horizontal acceleration
not exceeding 1 m/s2, and at any course, especially at 45°, 90° and
315° should not exceed ±1° ✕ secant latitude.
4.2.4 When subject to the environmental conditions referred to in
resolution A.694(17),footnote the error should not exceed ±1°.
4.2.5 The maximum divergence in reading between the master compass
and the steering and visual bearing equipment under all operational conditions should
not exceed ±0.5°.
4.2.6 The follow-up rate of the transmission system should be at
least 20°/s.
5
Power Supply
The gyro-compass should be provided with an uninterruptable power
supply.
6
Construction and Installation
6.1 The master gyro-compass should be installed in a craft with the
fore and aft datum lines parallel to the craft’s fore and aft datum line to within
±0.5°. The lubber line should be in the same vertical plane as the centre of the card of
the compass and should be aligned accurately.
6.2 Means should be provided for correcting the errors induced by speed and
latitude. An approved accurate speed source should be used for automatic speed
corrections.
6.3 A status signal should be provided to indicate that the gyro-compass is ready
for use.
6.4 An alarm signal should be provided to indicate that the gyro-compass has
suffered an external power supply failure or an internal system functional failure which
would invalidate the heading information.
6.5 The system should be designed to enable heading information to be provided to
other navigational aids such as radar, ARPA, radio direction-finder and automatic pilot.
The accuracy of the other navigational aids must not be degraded, and should continue to
comply with the standards specified for such aids.
7
Interface
The gyro-compass equipment should provide an output of heading information
with an accuracy as defined in 4 when interfaced by other equipment.